514-336-3820
514-745-1764
Series 230
Diamond Grind
Down Cut
Series 231
Diamond Grind
Down Cut
End Mill Type
Series 231B
Diamond Grind
Down Cut
Bur End
Series 231D
Diamond Grind
Down Cut
Drill Point
Series 231F
Diamond Grind
Down Cut
Fishtail
Designed for
routing of glass-reinforced printed circuit boards, phenolic-epoxy
and other highly abrasive materials.
Routers are down cut to hold the circuit board tight
to the work table.
Ultra fine mirograin.
| Series
230 Part # |
Series
231 Part # |
Series
231B Part # |
Series
231D Part # |
Series
231F Part # |
Fraction or MM |
Flute Length |
Shank Diameter |
Overall Length |
| 23003120 | 23103120 | 23103120B | 23103120D | 23103120F | 1/32 | 1/8 | 1/8 | 1-1/2 |
| 23004690 | 23104690 | 23104690B | 23104690D | 23104690F | 3/64 | 5/32 | 1/8 | 1-1/2 |
| 23006251 | 23106251 | 23106251B | 23106251D | 23106251F | 1/16 | 3/16 | 1/8 | 1-1/2 |
| 23009370 | 23109370 | 23109370B | 23109370D | 23109370F | 3/32 | 3/8 | 1/8 | 1-1/2 |
| 23012500 | 23112500 | 23112500B | 23112500D | 23112500F | 1/8 | 1/2 | 1/8 | 1-1/2 |
| 23018750 | 23118750 | 23118750B | 23118750D | 23118750F | 3/16 | 5/8 | 3/16 | 2 |
| 23025000 | 23125000 | 23125000B | 23125000D | 23125000F | 1/4 | 3/4 | 1/4 | 2 |
| 23025010 | 23125010 | 23125010B | 23125010D | 23125010F | 1/4 | 3/4 | 1/4 | 2-1/2 |
| 23025020 | 23125020 | 23125020B | 23125020D | 23125020F | 1/4 | 3/4 | 1/4 | 3 |
| 23031250 | 23131250 | 23131250B | 23131250D | 23131250F | 5/16 | 7/8 | 5/16 | 2-1/2 |
| 23037500 | 23137500 | 23137500B | 23137500D | 23137500F | 3/8 | 7/8 | 3/8 | 2-1/2 |
| 23003150 | 23103150 | 23103150B | 23103150D | 23103150F | .8 MM | 3 | 1/8 | 38 |
| 23003940 | 23103940 | 23103940B | 23103940D | 23103940F | 1 MM | 4 | 1/8 | 38 |
| 23004720 | 23104720 | 23104720B | 23104720D | 23104720F | 1.2 MM | 4 | 1/8 | 38 |
| 23005910 | 23105910 | 23105910B | 23105910D | 23105910F | 1.5 MM | 5 | 3.0 | 38 |
| 23005911 | 23105911 | 23105911B | 23105911D | 23105911F | 1.5 MM | 5 | 1/8 | 38 |
| 23006300 | 23106300 | 23106300B | 23106300D | 23106300F | 1.6 MM | 5 | 1/8 | 38 |
| 23007870 | 23107870 | 23107870B | 23107870D | 23107870F | 2 MM | 8 | 1/8 | 38 |
| 23009450 | 23109450 | 23109450B | 23109450D | 23109450F | 2.4 MM | 9.5 | 1/8 | 38 |
| 23011810 | 23111810 | 23111810B | 23111810D | 23111810F | 3 MM | 12.5 | 3.0 | 38 |
| 23011811 | 23111811 | 23111811B | 23111811D | 23111811F | 3 MM | 12.5 | 1/8 | 38 |
| 23019680 | 23119680 | 23119680B | 23119680D | 23119680F | 5 MM | 16 | 5.0 | 51 |
| 23023620 | 23123620 | 23123620B | 23123620D | 23123620F | 6 MM | 19 | 6.0 | 51 |
| 23031500 | 23131500 | 23131500B | 23131500D | 23131500F | 8 MM | 22 | 8.0 | 64 |
***Discontinued, subject to stock availability***
Recommended for general purpose routing of most non-ferrous and non-metallic materials.
Single flute geometric's offer the
most flute volume for chip removal.
Three flute designs offers best work piece
finish.
Lighter cuts must be taken while end cutting.
Two flute geometry is a good compromise
between flute volume, rigidity and work piece finish.
All tools are designed with geometric's
for machining aluminum's, magnesium's, hardwoods, hard
rubber, brasses, bronze, composites and plastics.
Series 232
Straight Flute
Two Flute
Series 233
Straight Flute
Single Flute
Series 234
Right Hand Spiral
Single Flute
Series 235
Left Hand Spiral
Single Flute
Series 236
Left Hand Spiral
Three Flute
Series 237
Left Hand Spiral
Two Flute
| Series 232 Part # |
Series 233 Part # |
Series 234 Part # |
Series 235 Part # |
Series 236 Part # |
Series 237 Part # |
Size | Flute Length |
Shank Diameter |
Overall Length |
| 23312500 | 23412500 | 23612500 | 23712500 | 1/8 | 1/2 | 1/8 | 1-1/2 | ||
| 23218750 | 23318750 | 23418750 | 23618750 | 23718750 | 3/16 | 5/8 | 3/16 | 2 | |
| 23325000 | 23425000 | 23525000 | 23625000 | 23725000 | 1/4 | 3/4 | 1/4 | 2-1/2 | |
| 23531250 | 5/16 | 13/16 | 5/16 | 2-1/2 | |||||
| 23237500 | 2337500 | 23437500 | 23537500 | 3/8 | 7/8 | 3/8 | 2-1/2 |
Tell us more about your experience with Airtek Ltd
Due to the fact that we are continuously improving our products, the descriptions, illustrations,
specifications,dimensions, and part numbers are subject to change without notice.
Every effort has been made to have the information on this site error free, we can not be responsible for errors and or omissions.
Airtek (1990) Ltée, 5750 Donahue St., Montreal, Qc, Canada, H4S 1C1
Tel: 514-336-3820