|
|
|
| Air Tools |
| Nile Pneumatic Tools |
| |
|
The blade is heated by a heater and these heat power
cutters most suitable for cutters are most suitable for
cutting hard and break-easy plastics such as acrylic resins,
etc.
A transformer is needed for the heat air nippers.
Blades are sold separately
Special blades are available upon special request.
|
PART
NUMBER |
OVERALL
LENGTH |
WEIGHT |
DIAMETER
OF BODY |
AIR
CONSUMPTION |
BLADE
NUMBER |
CUTTING
CAPACITY |
| AH10 |
200MM |
560G |
45MMø |
130 CM/STROKE |
FA50 |
4.5MM
(HARD PLASTICS) |
| AH12 |
200MM |
570G |
45MMø |
131 CM/STROKE |
FA50 |
5.5MM
(HARD PLASTICS) |
Temperature of the Blade 90°C - 150°C
Needing 25 Minutes to get to maximum temperature.
|
| Suitable for narrow plate, plastic plate and wire net |
 |
 |
| AS |
ASP
(With pressure increase mechanism) |
PART
NUMBER |
OVERALL
LENGTH
IN MM |
WEIGHT
IN
GRAMS |
DIAMETER
IN MM |
AIR
CONSUMPTION |
AIR
PRESSURE |
CUTTING
CAPACITY |
| AS-100 |
139 |
230 |
36 |
116 CM3 / stroke |
62-85 PSI |
0.5 MM Plate |
| AS-200 |
166 |
500 |
45 |
230 CM3 / stroke |
62-85 PSI |
1.0 MM Plate |
| ASP-150 |
211 |
300 |
36 |
223 CM3 / stroke |
62-85 PSI |
0.8 MM Plate |
| ASP-250 |
253 |
720 |
45 |
500 CM3 / stroke |
62-85 PSI |
1.2 MM Plate |
|
|
When the lever is pressed, the blade catches the wire
and rotates to twist it.
|
SP-40W |
BEFORE
AFTER |
WT-06 |
PART
NUMBER |
OVERALL
LENGTH
IN MM |
WEIGHT
IN GRAMS |
DIAMETER
IN MM |
AIR
CONSUMPTION |
AIR
PRESSURE |
CUTTING
CAPACITY |
| WT-06 |
225 |
800 |
38 |
0.45 M3 / MIN |
70 - 85 PSI |
1.0 MM
Steel Wire |
1.2 MM
Copper Wire |
| SP40W |
245 |
1200 |
38 |
0.45 M3 / MIN |
70 - 85 PSI |
1.2 MM
Steel wire |
2.0 MM
Copper Wire |
|
|
Versatile to cut a wide variety of materials, from
light sheet metal to plastics as well as carpet.
Good for cutting and trimming thinner sheets of rubber
or vinyl cloth, paper, etc.
|
 |
PART
NO. |
OVERALL
LENGTH
IN MM |
WEIGHT
IN GRAMS |
DIAMETER
IN MM |
AIR
CONSUMPTION |
AIR
PRESS. |
| GS-01 |
140 |
500 |
36 |
0.45 M3 / MIN |
55 - 85 PSI |
BLADE NUMBER 10M |
| Can be used for automobile
body work and sheet metal processing, wood work, removing
rough edges of small metal precisions parts, finishing,
rust removal and polishing. |
MB-20
For use in narrow confined places
or for spot grinding. |
MB-20S
Its three point construction makes the grinding of
flat surfaces easier. |
 |
 |
PART
NUMBER |
BELT
W x L
IN MM |
OVERALL
LENGTH
IN MM |
WEIGHT
IN GRAMS |
BELT
SPEED
AT
NON LOAD |
AIR
CONSUMPTION |
AIR
PRESSURE |
| MB-20 |
20 X520 |
250 |
930 |
2200 M / MIN |
0.3 M / MM3 |
70 - 85 PSI |
| MB-20S |
20 X520 |
250 |
1080 |
2200 M / MIN |
0.3 M / MM3 |
70 - 85 PSI |
|
| 3-5 Times faster hand operation |
BEFORE & AFTER |
 |
 |
PART
NUMBER |
OVERALL
LENGTH
IN MM |
WEIGHT
IN GRAMS |
DIAMETER
IN MM |
AIR
CONSUMPTION |
AIR
PRESSURE |
| RC-6 |
180 |
830 |
38 |
0.45 M3 / MIN |
70 - 85 PSI |
|
|
IT'S A SAW. IT'S A FILE.
It cuts automobile panels and metal pipes, and all it
takes for the user to get started is a small hole.
With file, holes in sheet metal and be enlarged (to install
a car antenna or other auto accessory), holes in panels
can be better matched, molds filed, castings de-burred
and paint scrapped.
It cuts an iron plate (thickness: 1mm)
At the rate of 400 mm a minute AF-5
At the rate of 900 mm a minute AF-10 |
 |
- Power boost switch for
easy cutting thick materials.
- Quiet operation and exhaust
is away from user.
- Rubber-covered body provides
comfortable usage and a good grip.
- Saw and file form a one-piece
unit. Any ordinary hacksaws (High Speed Steel made)
can be shortened and easily attached. (Only AF-10)
|
PART
NUMBER |
BODY
LENGTH
IN MM |
BODY
WEIGHT
IN GRAMS |
GRIP
SIZE
IN MM |
AIR
CONSUM. |
AIR
PRESSURE |
STROKE
IN MM |
STANDARD
ATTACHMENTS |
| AF-5 |
163 |
400 |
29 |
0.2 M3 / MIN |
78 - 92 PSI |
5 |
2 Saw Blades
1 Blade Holder
1 Each Flat, Round &
Triangular Files |
| AF-10 |
233 |
830 |
38 |
0.28 M3 / MM |
78 - 92 PSI |
10 |
3 Saw Blades
1 Each Flat, Round & Triangular
Files |
|
|
|
